Water Heater Replacement in Frisco, TX

Most tank water heaters last 8 to 12 years. When yours is leaking from the tank itself, or it is past ten years and needs an expensive repair, replacing it is usually the better money.

Illustrative photo of plumbers carrying a new gas water heater into a garage beside an old disconnected heater

Call for a price(972) 945-6903

Price guide: A 40-gallon gas tank typically runs $1,600 to $2,700 installed, and a 50-gallon gas tank $1,800 to $3,000. Electric tanks run $1,300 to $2,300 for 40 gallons and $1,500 to $2,500 for 50. That includes the city permit, connections and hauling the old one away. An attic install adds about $300 to $800.

These are typical prices for the Frisco area, to help you plan. Every home is a little different, so your price is confirmed with you before any work starts.

What the visit involves

The plumber shuts off the gas or power and the water, drains the old tank, and disconnects it. The new heater goes in on a drain pan, with new supply connectors, a new temperature and pressure relief line, and the gas line or wiring reconnected and tested. If the house has a pressure regulator or a check valve on the water main, an expansion tank goes in too.

Then the tank is filled, the air is bled from the lines, and the burner or elements are fired and checked. Most straight swaps in a garage take two to four hours. An attic unit, or a switch from tank to tankless, takes longer. The city inspector checks the work after the permit is pulled.

Repair or replace?

A rough rule: if the repair costs more than about half the price of a new heater, or the tank is past ten years, replace it. Some faults are always a replacement:

Parts are usually worth fixing on a younger heater: a thermocouple, igniter, gas valve, element, thermostat or relief valve. See water heater repair in Frisco for those.

What size water heater do you need?

For a tank, the number that matters is the first-hour rating on the yellow label: how many gallons of hot water it can deliver in a busy hour. As a starting point:

Gas heaters recover faster than electric ones, so a 40-gallon gas tank keeps up with roughly what a 50-gallon electric does. Our sizing guide works it out from your household.

Permits and code in Frisco and Collin County

Replacing a water heater in Texas is plumbing work. It has to be done by a licensed plumber, and Frisco and the surrounding cities require a permit and an inspection. The inspector looks at the things that make a heater safe:

The permit is in our price. A heater put in without one can come up when you sell the house.

Gas, electric, heat pump or tankless?

Most homes in Frisco built since the 1990s have gas water heaters, often in the garage or the attic. Like for like is the cheapest swap. Switching type costs more because it means new gas lines, wiring or venting.

Helpful answers

Questions people ask

How long does a water heater last in North Texas?

A tank water heater usually lasts 8 to 12 years. Hard water shortens that because scale builds up in the tank, so flushing it once a year and checking the anode rod helps. Tankless units often last 20 years with regular descaling.

How much does it cost to replace a water heater in Frisco?

A 40 or 50-gallon gas tank typically runs $1,600 to $3,000 installed, including the permit and haul-away. Electric tanks run a little less. An attic install, an expansion tank or a switch to tankless adds to it.

Do I need a permit to replace a water heater in Frisco?

Yes. Frisco and the surrounding cities require a plumbing permit and an inspection for a water heater replacement, and the work must be done by a Texas-licensed plumber. The permit is included in our price.

How long does a water heater replacement take?

A like-for-like swap in a garage usually takes two to four hours. An attic install or a switch from a tank to tankless can take most of a day.

Related

Cities we cover around Frisco

Also covered: Hackberry, Oak Point, Cross Roads, Aubrey, Parker.

Ask for a call back